Geely Emgrand Workshop Manuals and Repair Manuals

To change the oil in your Geely Emgrand, first locate the oil pan underneath the car and remove the drain plug to drain the old oil. Then, remove the oil filter and replace it with a new one. Finally, refill the engine with the recommended type and amount of oil specified in the owner's manual.

To check the engine coolant level in your Geely Emgrand, first make sure the engine is cool. Locate the coolant reservoir, usually near the radiator. Check the level of the coolant in the reservoir and add more if necessary. Be sure to use the correct type of coolant specified in the owner's manual.

To check the transmission fluid in your Geely Emgrand, first make sure the engine is warm and running. Then, locate the transmission dipstick, usually near the back of the engine bay. Remove the dipstick, wipe it clean, reinsert it, and remove it again to check the fluid level. Be sure to use the correct type of transmission fluid specified in the owner's manual.

To jump start your Geely Emgrand, first park the donor vehicle close to your car and turn off both engines. Connect the positive (+) jumper cable to the positive terminal on the donor battery, then to the positive terminal on your car's battery. Connect the negative (-) jumper cable to the negative terminal on the donor battery, then to a metal part of your car's engine away from the battery. Start the donor vehicle and let it run for a few minutes, then start your car. Disconnect the cables in the reverse order.

To replace a fuse on your Geely Emgrand, first locate the fuse box, usually under the dashboard or in the engine bay. Use the fuse diagram in the owner's manual to locate the fuse that needs to be replaced. Use a fuse puller or pliers to remove the old fuse and replace it with a new fuse of the same amperage rating.

To replace a headlight bulb on your Geely Emgrand, first locate the back of the headlight assembly. Unplug the wiring connector and remove the retaining clip or screw holding the bulb in place. Remove the old bulb and install the new one, being careful not to touch the glass with your fingers. Reattach the retaining clip or screw and plug in the wiring connector.

To replace a taillight bulb on your Geely Emgrand, first locate the back of the taillight assembly. Twist the bulb holder counterclockwise to remove it from the assembly. Remove the old bulb and install the new one, being careful not to touch the glass with your fingers. Reattach the bulb holder by twisting it clockwise back into the assembly.

To replace the air filter in your Geely Emgrand, locate the air filter housing under the hood. Open the housing and remove the old filter, making note of its orientation. Install the new filter in the same orientation and close the housing. Be sure to use the correct air filter specified in the owner's manual.

To replace the brake pads on your Geely Emgrand, first jack up the car and remove the wheel. Locate the brake caliper and remove the mounting bolts to remove the old brake pads. Install the new brake pads and reassemble the caliper. Be sure to properly torque the bolts and bed in the new brake pads according to the manufacturer's recommendations.

To replace the cabin air filter in your Geely Emgrand, locate the cabin air filter housing, usually behind the glove box or under the dashboard. Open the housing and remove the old filter, making note of its orientation. Install the new filter in the same orientation and close the housing. Be sure to use the correct cabin air filter specified in the owner's manual.

To replace the serpentine belt on your Geely Emgrand, first locate the belt routing diagram under the hood. Use a wrench or tensioner tool to release the tension on the belt and remove it from the pulleys. Install the new belt according to the routing diagram and release the tensioner. Be sure to properly tension the belt according to the manufacturer's recommendations.

To replace the spark plugs in your Geely Emgrand, first locate the spark plug wires or coil packs. Use a spark plug socket and ratchet to remove the old spark plugs. Install the new spark plugs, being careful not to overtighten them. Reattach the spark plug wires or coil packs. Be sure to use the correct spark plugs specified in the owner's manual.

To replace the windshield wiper blades on your Geely Emgrand, first lift the wiper arm away from the windshield. Press the release tab on the wiper blade connector and slide the blade off the arm. Install the new blade by sliding it onto the arm until it clicks into place. Lower the wiper arm back onto the windshield.

To reset the maintenance light on your Geely Emgrand, first make sure the odometer is displaying the trip meter. Turn off the engine and press and hold the trip meter reset button. While holding the button, turn the ignition on (but not the engine) and continue holding the button until the maintenance light turns off. Release the button and turn off the ignition.

The recommended tire pressure for your Geely Emgrand can usually be found on a sticker located inside the driver's side door jamb. It is important to maintain the proper tire pressure for optimal handling, fuel efficiency, and tire life. Be sure to check the tire pressure regularly, especially before long trips.